HARMAN KARDON AVR65
Manual de Servicio

Remote Control

select a surround mode. To change the surround mode, first press the SURR/CH button . Next press these

Numeric Keys : These buttons serve as a ten-button numeric key-pad to enter tuner preset positions. They are also to be used to select channel numbers when TV has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

indicator

.

to enter your choice. Speaker Configuration : Press this button to begin the process of configuring the AVR-65's Bass Management System for use with the type of speaker used in your system.

Clear Button : This button dose not function with the AVR-65, but it is available for use with other devices.

buttons to scroll up or down through the list of surround modes that appear in the Information Display . These buttons are also used to

increase or decrease output levels used to lower the AVR-65's output levels when configuring the unit with either the internal test tone or and external source. They are also used to enter delay time settings after the Delay button been pressed. has

Press Up/Down : When the tuner is in use, these buttons scroll through the stations that

Once the button has been pressed, use the buttons

/

to select the channel you wish to set , and then select

NOTE : The 0 button has a dual function. It also serves as the CLEAR button for use in programming the tuner or clearing the system memory.

have been programmed into the AVR-65's memory, When many source devices, such as CD players, VCRs and cassette decks, are selected using the Device Control Selectors these buttons will normally function as chapter .

up. Press the Set button

another channel to configure. When all adjustments have been completed, press the Set button twice to exit the settings and return to normal operation.

/

Channel Button : This button is used

Direct/Enter : Press this button to select a radio station by entering its frequency using the Numeric Key .

step or track advance. Surround Mode Selector : Press this Tuning Up/Down : When the tuner is in use, these buttons will tune up or down through the button to begin the process of changing the surround mode. After the button has been pressed, use the / buttons to select the

to start the process of setting the AVR-65's output levels to an external source. Once this button is pressed, use the / buttons to

select the channel being adjusted, then press the Set button , followed by the / buttons

Memory Button : Press this button to enter a radio station into the AVR-65's preset memory. After pressing the button the MEMORY indicator will flash, and you then have five seconds to

selected frequency band. If the Tuner Mode button indicator has been pressed so that the AUTO is illuminated, pressing these

desired surround mode. Note that this button is also used in the "Auto Search" process.

again to change the level setting.

buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the AUTO indicator is NOT Volume : Press these buttons to raise or lower the system volume.

Set Button : This button is used to enter settings into the AVR-65's memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

enter a present memory location using the Numeric Keys .

illuminated, pressing these buttons will tune NOTE : Although the word "Sleep" appears above this button, it refers to control of devices other than the AVR-65. Use the Sleep button Transport Control : These controls do not control any function of the AVR-65, but they are used extensively when operating a wide variety OSD Button : This button dose on screen display function with the AVR-65. Semi Full OFF Delay/Prev Ch. : Press this button to begin the process for setting the delay times used by Light Button : Press this button to activate the remote's built-in back-light for better legibility of the buttons in a darkened room. the AVR-65 when processing surround sound. After pressing this button the delay times are entered by pressing the Set button using Tuner Mode : Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so that the AUTO indicator goes out, / Digital Button : This button is used to When the AVR-65 remote is being programmed for the codes of another device, this button is also used in the "Auto Search" process. / buttons , and then Note that this button is also used to change channels on your TV when the TV is selected using the Devise Control Selector . 30 20 10 5 1 OFF 90 80 70 60 50 40 of CD players, cassette decks and VCRs. stations in single-step increments. Sleep Button : Press this button to place the unit in the Sleep Mode. After the time shown in the display, the AVR-65 will automatically go into the standby mode. Each press of the button changes the time until turn-off in the following order:

Night Mode : Press this button to activate the "Night" mode, preventing loud playback when the digital modes are in use without altering the dynamic range of the output signal.

to control the AVR-65's Sleep function.

AVR Selector : Press this button to use the remote control for operation of the AVR-65. Note that the button will briefly turn red after it has been pressed to confirm your selection.

Mute : Press this button to momentarily silence the AVR-65 or TV set being controlled, depending on which device has been selected.

When the AVR-65 remote is being programmed to operate other devices, this button is pressed to begin a readout of a programmed code.

Test : Press this button to begin the Device Control Selectors : Press one of these button to use the remote to control the functions of another audio/video device. Note that the button will briefly turn red after it has been pressed to confirm your selection. Display/Multiroom Button : This button does not function with AVR-65, but it is available for use with other devices. Power Button : Press this button to turn the currently selected device on or off. Buttons : These are multi purpose buttons. They will be used most frequently to sequence used to calibrate the AVR-65's output levels.

Source Selectors : Press these buttons to select an input source for the AVR-65. The AM/ FM button is also used to switch between frequency bands when the tuner in use.

to change the setting.

Press the Set button again to complete the process.

NOTE : Pressing one of these buttons selects the source only. In order to control the actual source machine using the remote you must press the Press Control Selector button the desired product. for

pressing the Tuning buttons

will move the

select the type of digital input used with any one of the input sources connected to the AVR-65. After pressing this button, use the / buttons

frequency up or down in single-step increments. When the FM band is in use, pressing this button when a station's signal is weak will change to monaural reception, as indicated by the MONO

(7) to make your selection between OPTICA or COAXIAL digital. Press the Set button

-7-